• Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine
  • Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine
Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine

Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine

제품 상세 정보:

원래 장소: 중국
브랜드 이름: Vector
인증: CE
모델 번호: VEC-VC-00733HC-m-e / 130MB-00220A33F-MF2

결제 및 배송 조건:

최소 주문 수량: 1개 장비
가격: To Be Discussed
포장 세부 사항: 280*208*78mm
배달 시간: 3-5 작업 일수
지불 조건: 전신환, 웨스턴 유니온, L/C (신용장)
공급 능력: 500개 장비 / 달
최고의 가격 접촉

상세 정보

전압: 380V 힘: 2개 KW
정격 전류: 5.1 A 정격 속도: 2000 분당 회전수
평가된 토크: 10nm 단계: 3 단계
모터 플렌지 사이즈: 130 밀리미터 통신 프로토콜: Modbus/CANopen/EtherCAT
부호기: 2500은 점진적 + 홀 부호기를 정렬시킵니다 애플리케이션: 인쇄기
하이 라이트:

Asynchronous Remote Control Servo Kit

,

2000rpm Remote Control Servo Kit

,

2000rpm Servo Motor Kit

제품 설명

2000rpm Three Phase Asynchronous Servo Motor Drive For Printing Machine

 

Servo System Kit

Power Range Covers 200W-110KW

Single/Three Phase 200V/400V

Modbus / CanOpen / EtherCAT

2500 line incremental + Hall encoder;

 

Products Description

 

Products Three Phase Asynchronous Servo Motor Drive
Brand Vector
Model No. VEC-VC-00733HC-M-E / 130MB-00220A33F-MF2
Power 2KW
Voltage 380V
Phase Three Phase
Rated Speed 2000 rpm
Rated Current 5.1A
Rated Torgue 10Nm
Communication Protocols Modbus/CANopen/EtherCAT
Encoder 2500 line incremental + Hall encoder; 

 

Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 0

The panel contains 8 buttons and 5 digital tubes. Only 5 of the 8 buttons can be used, and the remaining

3 buttons reserved. The general functions of the five buttons are shown in the table below.

Key Name Key function
PAR/ALM mode switch, return to the previous menu
▲(add) increase flashing bit value of the LED digital tube
▼(dec) Decrease flashing digit value of the LED digital tube
STOP/RST Moves the blinking LED tube to the left; checks the high value of data
longer than 5 bits; Fault reset;execute Fn function
RD/WT read/write parameter values;enter fn page

 

Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 1


Servo Drive Description- Detaails about a Servo Drive, how to select the Servo drive model and do installation?

 

● Install the driver on a dry and sturdy platform. Maintain good ventilation and

heat dissipation during installation and maintain good grounding.

● Please install in the specified direction to avoid malfunction.

● When installing, please ensure that the servo driver is kept at a specified

distance from the inner surface of the cabinet and other machines, otherwise it may cause fire or malfunction.

Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 2

 

Installation
Environment
Requirements
Atmospheric Pressure 86~106kPa
Mbient Humidity 0~55℃
Ambient Temperature 0~90%RH
IP Rating IP20
Vibration 0~4.9m/s^2

 

● When installing, do not block the suction and exhaust ports, and do not allow foreign objects inside the

product to enter, otherwise it may cause malfunction or fire due to aging of internal components.

● Do not place heavy objects on or under this product as this may result in injury.

● Please install in the following environment:

1.places without direct sunlight;

2.Locations where the ambient temperature is in the range of 0 ° C to 55 ° C;

3.Relative humidity in the range of 0% to 95%, and no condensation;

4.Locations free of water droplets, vapors, dust and oily dust;

5.Locations where there is no high heat device;

6.Non-corrosive, flammable gas and liquid sites;

7.It is not easy to splash water, oil and medicine;

8.places that are not exposed to radioactive radiation;

9.Strong and vibration-free places;

10.Locations where there is no electromagnetic noise interference.

 

Wiring precautions

● It is recommended not to use single-phase 220V for main power supply,

which may cause damage to electrolytic capacitor due to lack of phase.

● Do not change the wiring during power-on, otherwise it may cause electric

shock or injury.

● Please perform wiring or inspection by professional technicians, otherwise it

may cause electric shock or product failure.

● Please carefully confirm the wiring and power supply. The output circuit

may be short-circuited due to wiring errors or application of different voltages. The brake does not operate

when the above fault occurs, which may result in mechanical damage or personal injury.

● Do not connect the input power cable to the U, V, and W terminals of the

drive. Otherwise, the servo driver will be damaged.

● When wiring, do not pass the power cable and signal cable through the same

pipe, and do not bundle them together. The distance between the two should be more than 30cm to avoid interference.

● The driver ground terminal must be grounded to avoid leakage and reduce

the interference of the system, and the diameter of the ground wire should be the same as or above the power supply line.

● When connecting the AC power supply and DC power supply to the servo unit, connect to the specified terminal.

Failure to do so may result in malfunction or fire.

● For the wiring length, the command input line is up to 3m and the encoder

line is up to 20m.

● Use a twisted-pair shielded cable for the signal cable and encoder cable, and

ground the shield with a single end.

●The U, V, W terminals of the driver and the U, V, and W terminals of the

motor should be connected one by one according to the name. If it is wrong connected, the motor cannot operate normally.

● Common DC bus products require pressure sensitive resistors and the wiring

is secure.

● Please check the power after the power is off for at least 5 minutes. Even if

the power is turned off, high voltage may remain inside the servo drive. Therefore, do not touch the power terminal

within 5 minutes after the power is turned off, otherwise it may cause electric shock.

● Do not turn the power ON/OFF frequently. When it is necessary to

continuously turn ON/OFF the power, please control it once or less in 1 minute. Since the power supply section

of the servo driver has a capacitor, a large charging current (charge time of 0.2 seconds) flows during the ON/OFF

power supply. Therefore, if the power is turned ON/OFF frequently, the performance of the main circuit components

inside the servo driver will be degraded.

● Do not apply power when the terminal block screws are loose or the cable is

loose. Otherwise, it may cause fire.

● Take appropriate shielding measures in the following locations, otherwise

the machine may be damaged:

1. Locations that cause interference due to static electricity;

2. A place that produces a strong electric field or a strong magnetic field;

3. Locations where there may be radiation radiation;

4. A place with a power cord nearby.

 

Accessorries:

 

  Accessory name Image  
Satandard Spare Parts Power terminal Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 3 Adapt to E1,E2 structure drive
Cn3 encoder plug Encoder plug on the driver side
Cn4 control terminal plug Input/output signal terminals,user wiring
Encoder connection line The standard cable length is 3, 5, 8, 10, 13, 15 meters, according to customer
needs Provide independent connector
Power line The standard cable length is 3, 5, 8, 10, 13, 15 meters, according to customer
needs Provide independent connector
Drive monitoring line Connect and adjust the software for remote monitoring and firmware update
Purchasing Spare Parts USB to RS232 Adapter cable If necessary, self purchase
Ethernet communication line If necessary, self purchase

 


Certificates

1. CE (EU Safety Standard);
2. IEC/EN61800-5-1:2007 (Safety requirements for electrical, thermal and energy in Section 5-1 of the variable

speed electric driver system), corresponding to the national standard GB12668.501-2013;

3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system part 3 electromagnetic compatibility standards

and its specific test methods), corresponding to the national standard GB12668.3-2012.

Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 4

 

Other Questions:

Q1. How to select the suitable model?
A: Please confirm your requirements for Rated Power, Current, Voltage,

Torque and select the suitable model based our model list;

 

Q2. How to set the programming system?
A: Our Servo drive support the Global Communication protocols: Modbus/CANopen/EtherCAT,

Please Just make the programming follow your experiences;

 

Q3. What's the power range about our servo system?
A: Our Power range covers 0.2-110KW, reach your requirements;

 

Q4. What's the encoder feedback interfaces we using?
A: We have multiple Encoder feedback interfaces, like : incremental/wire-saving encoder,

17-bit/23-bit/24-bit absolute encoder, resolver encoder, etc.

 

Maintenance and inspection Precautions

● do not change the wiring while the power is on, otherwise it may cause electric shock or injury.

● please perform wiring or inspection by professional technicians, otherwise it

may cause electric shock or product failure.

● please check the power after the power is off for at least 5 minutes. Even if the power is turned off, high

voltage may remain inside the servo drive. Therefore, do not touch the power terminal within 5 minutes after

the power is turned off, otherwise it may cause electric shock.

●when replacing the servo drive, please back up the servo driver user parameters to be replaced before the replacement,

and transfer the backup to the new servo drive, and then restart the operation, otherwise the machine may be damaged.

 

Payment Terms
Samples: 100% before delivery by Western Union.
Bulk Orders: 30% deposit, 70% before shipping by T/T or Western Union.
           
Production Time
Small orders 3-5 work days
Production capacity can reach 1000 kits per month.

 

Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 5

 

 

이 제품에 대한 자세한 내용을 알고 싶습니다
나는 관심이있다 Asynchronous 2000rpm Remote Control Servo Kit For Printing Machine 유형, 크기, 수량, 재료 등과 같은 자세한 내용을 보내 주시겠습니까?
감사!
답변 기다 리 겠 습 니 다.